Infographics Archive |
| Which Vehicles Last the Longest? Posted: 01 Jun 2022 06:03 AM PDT What is the most important consideration when looking to buy a new car? Many people look into safety ratings, luxury features, and fuel economy when researching new vehicles. One important thing that should also be considered is vehicle longevity. When properly maintained, cars that last a long time can save a lot of money over the years. Do you know which cars have the highest likelihood of lasting 200,000 miles or more? The AlansFactoryOutlet.com team looked at longevity data to determine which vehicles had the highest rate of going 200,000 miles or more. The following are the 10 automobiles that came out on top along with the percentage of each vehicle that has lasted 200,000 miles or more:
The car at the top of the list is the Toyota Land Cruiser, with 18.2% lasting more than 200,000 miles. Toyota is the clear winner overall, with nine vehicles making the list of top 20 vehicles. Second on the list is the Toyota Sequoia, with 14.2% of these vehicles going more than 200,000 miles. Coming in third is the Chevy Suburban. 6.6% of Suburbans go more than 200,000 miles. Overall, 2.3% of Toyota vehicles last more than 200,000 miles, making it the longest lasting auto manufacturer. The second brand that lasts the longest overall is Honda (1.9%). Close behind in third place is GM, with 1.8% of their cars lasting 200,000 miles or more. Whether you drive one of the long-lasting automobile on the list or another car, preventative maintenance and taking care of your vehicle can help it last much longer.  The post Which Vehicles Last the Longest? appeared first on Infographics Archive. |
| How To Make Your Own Lightsaber (Infographic) Posted: 31 May 2022 11:28 PM PDT There’s always that one guy who brings a knife to a gunfight! But what if, just once, you could harness the power of the force with a lightsaber? Isn’t every Star Wars fan’s dream to wield the legendary lightsaber to blast through enemies and doors alike? And even though we don’t currently have the required technology to build a real one, you will have a lot of fun creating your own lightsaber toy using our DIY infographic below. What Is A Lightsaber?Of course, if you’re a Star Wars fanatic, then you already know all about this infamous weapon, but let’s take a few moments to discuss what it is for those who are unfamiliar. A lightsaber, ren, or laser sword, is a fictional weapon that’s shown throughout the Star Wars franchise. Typical versions of them feature luminescent plasma blades and are the signature weapon for the Knights of Ren, Jedi Order, and the Sith Order. While Jedi tend to use lightsabers that are yellow, green, or blue, the Sith use red sabers, so there are many variations of this weapon. According to surveys, the lightsaber is the most recognizable element from the Star Wars franchise, with many fans believing it’s the most popular weapon in all of film history. In films, lightsabers have the ability to burn, melt, and cut through most substances with little to no resistance. It can also be used to battle enemies, in which the weapon leaves behind cauterized wounds on flesh. However, the lasers can be deflected by energy shields and other blades.  How To Make A Lightsaber At HomeNow that we all know precisely what a lightsaber is, let’s go over how to build your own replica at home. Below you’ll find everything you need to complete this project, from required materials to the step-by-step process. What Materials Do I Need?Before you build your own lightsaber, there are some materials you’ll need to obtain. Here’s what you’ll need to create the blade and handle: The Handle
The Blade
It’s important to note that the materials we’ve listed above are just suggestions; if you’re a crafty person and want to substitute other materials, that’s perfectly fine! The only thing you must make sure of is that the inner diameter of the handle is more than that of the blade’s diameter. So, in theory, you could use anything from a tennis racket to some other form of tubing. When it comes to the blade, it’s better to use opaque tubing rather than a straight transparent variety. This will help the appearance of your LED lights, as you want them to have a more “cloudy” appearance. If you have no other option than to use clear tubing, you can always use some sandpaper to rough up the surface. What Tools Do I Need?Along with the appropriate materials, there are also a host of tools you should round up before starting. To make things easier, we’ve compiled them into a list below:
 Step-By-Step Guide – How To Make A Custom LightsaberSo, by now, you have all of the materials and tools required to make your own lightsaber, and it’s time for the fun part! Just don’t forget to improvise where you can and add your own personal touches to show everyone just how creative you are! Let’s get right into the step-by-step guide to build your own lightsaber: Building Your Own Lightsaber HandleStep #1The handle is extremely easy to make out of PVC pipe. Once you have your chosen type, simply use your hacksaw or PVC cutter to make your handle the appropriate size. The standard size for a lightsaber blade is 10″, but it can be more or less, depending on your height.
Step #2Lay down a piece of cardboard and paper, and use your chosen spray paint color to coat the handle. This step can be done later but is best when done at the start and outdoors. Step #3Next, decide how long you want the inner tubes and cut them down to size. Once they are the right size, slip them over the handle to serve as grips. Step #4Now, it’s time to decide where your button will be placed. It’s suggested that you put it somewhere that’s accessible by your thumb while holding the lightsaber. For this step, you’ll need a correctly-sized drill bit to form a hole in which the button fits snugly. Step #5Then, you’ll need to cut a slit in the bottom of the handle where you can place the battery pack if you plan to use one. To achieve a nice hole, use either the PVC cutter or hacksaw, but don’t forget to sand down the edges, so they’re not rough. Step #6Finally, go ahead and randomly swing your handle around to get a feel for just how cool you’re going to look when it’s done. Then, set the handle to the side and start creating the blade.  Building Your Own Lightsaber BladeNow that your handle is done, it’s time to move on to the blade portion of your lightsaber. Here are the steps required to build it: Step #1The first step of creating a lightsaber blade is to cut your tubing down to your desired length. This cut can be made using a hacksaw or PVC cutter, but all rough edges will require sanding or deburring. As a general rule of thumb, two and a half feet is a good starting point, but be sure to measure the length with the Jedi, who will yield it for best results. And don’t forget, if your tube is clear, this is the time to rough it up with sandpaper in a lengthwise manner; do so until it turns white. Step #2Now, determine which end of the blade will serve as the tip and which will act as the base. Then, cut and shape the cable ties so that they cover the diameter of the tip but don’t leave any sharp edges. You will then need to glue the ties to either end, creating a bridge. This is important because it will be used to attach the LED lights, aka “the force,” when you are finished. Step #3Hold the tube so that you are looking at the base. Use a measuring tape to go up about 5 or 6 millimeters, where you’ll use a writing utensil to mark around the blade. Next, use this mark to begin wrapping the blade with PVC or duct tape, creating a wedge that fits into the handle. Just be sure that the fit is tight enough that your blade won’t fly out of the handle!  Creating “The Force”During this phase, you’ll focus on bringing “The Force” to your blade. Step #1Take the two wires that you cut down previously and strip them of all insulation. Step #2Take hold of one stripped wire and attach the positive side of the LED to the top of the wire. Please note that each LED features two legs; the longer of the two is the positive side. Step #3Now continue adding LEDs down the length of your stripped wire using the positive side. Each LED should sit where its neighbor’s tail ends. Step #4After you’ve achieved your desired length, work your way back up by attaching the negative sides. Just be sure not to mix up the positive and negative wires because you don’t want to go over to the dark side! Step #5If necessary, use pliers to crimp the wire ends, or you could also solder them. Step #6Take a look back through each of your LEDs to ensure they’re attached correctly. Keep in mind that just one short circuit is enough to prevent your lightsaber from having “The Force.” Step #7Next, carefully lower the string of LEDs into the blade, going over the bridge and attaching them to the bottom. We should also note that using a reflective bottom helps better keep the light inside the blade. The bridge helps keep the string of lights in place and ensures that they travel throughout the blade. Step #8Take aluminum foil to the tip as carefully as you can – this helps reflect the light back down the blade. Step #9It’s time to make sure your button fits in the hole that you created. If everything looks good, go ahead and feed the wires into the handle. Try not to squash the wires on the opposite wall when installing the button. Step #10Solder your wires to the switch/button and thread them through the hole until they come out the other end. Step #11Wedge your handle into place, and be sure to hold the wires so that they protrude from the bottom of your handle. Step #12If you decided that your lightsaber couldn’t live without a noise-making motor – let’s go ahead and install it now. Glue a nut or wrap a piece of wire onto the motor shaft to keep it balanced. This helps ensure that it vibrates more and creates more realistic sound effects. Step #13Solder off all of your wires in parallel so that your battery pack is in the middle. Step #14Finally, all that’s left is carefully inserting everything into the handle and making sure your motor does not get obstructed. The Bottom LineIn the end, the lightsaber is one of the most sought-after weapons from the Sci-Fi genre. Rather than waiting for the real technology to come out, go ahead and have fun designing your very own lightsaber! And the best part is – you don’t have to be a Jedi to do it! Original infographic via Herbertpocket, content updated June 2022.  The post How To Make Your Own Lightsaber (Infographic) appeared first on Infographics Archive. |
| You are subscribed to email updates from Infographics Archive. To stop receiving these emails, you may unsubscribe now. | Email delivery powered by Google |
| Google, 1600 Amphitheatre Parkway, Mountain View, CA 94043, United States | |
No comments:
Post a Comment